Castle MOTOR/RELGER 1/5 MAMBA XLX2 8S ESC 800KV

Castle MOTOR/RELGER 1/5 MAMBA XLX2 8S 33.6V ESC 20A PEAK BEC 2028-800KV SENSORED MOTOR

ESC Specs
Application Guidelines: 1:5th Scale vehicles weighing up to 30lbs (13,6kg) max with included Castle 2028 motor

Vehicle Examples: Losi DB XL-E™, Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™. Note: Some vehicles may require aftermarket parts to allow ESC and/or motor fitment.

Input Voltage Range:
MIN: 3S LiPo, MAX: 8S LiPo 33.6V

Running Modes:
Sensored, Sensorless, Brushed and SmartSense™ when paired with a Castle 4-POLE 12-SLOT Sensored Motor.

Brake:
Proportional

Reversible:
Yes, but may be disabled for racing.

On/Off Switch:
Yes, waterproof

Cooling Fan:
Yes, factory equipped (50mm), fully removable** (See Product Use Statements)

Size:
Length: 3.98” (101.2mm), Width: 2.49” (63.3mm), Height: 2.2” (55.8mm)

Weight (with wires):
13.1 oz (371g)

Motor Connectors:
8mm female bullets

Items Needed for Operation:
The Mamba XLX2 requires the use of connectors designed for 150+ amps continuous, such as Castle 6.5mm polarized or CC BULLET 8.0mm

Operating environment:
Waterproof design for all weather conditions (See Operating Environment Considerations)

Programmability:
Fully programmable Castle feature set using Castle Link USB adapter and freely downloadable Castle Link Windows software, or the Castle Link App and a B-LINK Bluetooth Adapter (sold separately).

Telemetry Link Capable:
Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX, T7PX and T7PXR Transmitters.

Tech Tips:
The Mamba XLX2 has threaded mounting holes on the bottom of the ESC. There are four M3 mounting holes with a maximum depth of 5mm; they are spaced 46mm wide and 40.2mm long. Use this template for assistance in alignment and screw hole positioning.

Motor Specs
Input Voltage Range:
12S max (8s max with XLX2)

Kv: 800

Max. RPM: 45,000

Motor Size: Length: 4.4" (113.2mm)

Diameter: 2.2" (57mm)

Shaft Size:
Length: 30mm
Diameter: 8mm

Weight (w/wires): 44 oz. / 1.25kg

Mounting Hole Specifications: 4mm @ 30mm spacing

Cooling Fan: Available, but not included (011-0019-00)

Connectors: 8.0mm male bullets.
Items Needed for Operation: N/A

Product Use Statements:
Do not use mounting screws that extend more than 5mm into the front of the motor. Using too long of a screw can result in damage to the motor's windings and will not be covered by the warranty.

Application Guidelines: N/A

Max. Recommended Vehicle Weight:
Vehicles weighing less than 30lbs (13,6kg)

Tech Notes:
Running modes: Sensorless and Sensored

Water Resistant Design:
The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommended applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to this document for running and maintaining motors in wet environments.