Cookie-Einstellungen
Diese Website benutzt Cookies, die für den technischen Betrieb der Website erforderlich sind und stets gesetzt werden. Andere Cookies, die den Komfort bei Benutzung dieser Website erhöhen, der Direktwerbung dienen oder die Interaktion mit anderen Websites und sozialen Netzwerken vereinfachen sollen, werden nur mit Ihrer Zustimmung gesetzt.
Benachrichtigung wenn Artikel wieder an Lager?
- Artikel-Nr.: 151128
- Hersteller-Nr.: RPM81312
- Bis 16 Uhr bestellt, Morgen Geliefert! (Lagerartikel)
- 30 Jahre RC Modellbau Erfahrung
- Top Service von Profi Modellbauer
- Über 500 Hersteller - 200`000 Artikel
81312 RPM Racing Products Tuning Parts Low Visibility Wheelie Bars for the Slash 2wd, Slash 4×4,... mehr
Produktinformationen "81312 RPM Low Visibiltiy Wheelie Bars Slash 4x4 Schwarz"
81312 RPM Racing Products Tuning Parts Low Visibility Wheelie Bars for the Slash 2wd, Slash 4×4, Losi SCTE & ECX Torment 4×4
Unser Tuning Tipp: RPM Teile sind aus nahezu unzerbrechlichem Nylon Kunstsoff für ungetrübten Fahrspass und ersetzen 1:1 das Originalteil
passt für: Slash 2WD, Slash 4x4, ECX Torment 4x4, Losi SCTE
nur für Fahrzeuge mit dem RPM Bumper Hinten
A serious issue with most currently available wheelie bars is the inability to use the truck as an off-road vehicle because most wheelie bars tend to stick out too far behind the truck. The RPM Low Visibility Wheelie Bar solves that problem! Since our wheelie bar and included wheels sits inside the protection of the rear bumper, they don’t stick out allowing the truck to function normally when rippin’ up the local track, yet still do their job when the occasional heavy finger pull yanks the front wheels off of the ground!
The RPM Low Visibility Wheelie Bar design bolts directly to all RPM Slash bumpers (both 2wd and 4×4), Losi SCTE & ECX Torment 4×4 at the mud flap mounts, while still allowing the use of RPM Mud Flaps (RPM #81012) as well as our Losi SCTE Bumper Mounts (RPM #73312! The RPM Wheelie Bar stays tucked up behind the rear bumper, yet sitting low enough to allow the wheels to touch down once the front end starts catching some serious air! Now any Slash, SCTE or Torment 4×4 owner can pull some sick wheel stands without the fear of grinding crucial rear bumper support components into dust!
RPM Low Visibility Wheelie Bars are sold ready to install on an RPM Rear bumper (sold separately) with all necessary mounting hardware and complete instructions for assembly. RPM Low Visibility Wheelie Bars are manufactured from our trademark blend of incredibly strong nylons and backed by our limited lifetime warranty again breakage.
Tech Notes: RPM Low Visibility Wheelie Bars are designed for use with RPM Slash 2wd and Slash 4×4 rear bumpers, ECX Torment 4×4 rear bumpers as well as our Losi SCTE Rear Bumper Mounts exclusively and will not work with stock Traxxas Slash rear bumpers, ECX Torment 4×4 rear bumpers or Losi SCTE rear bumper mounts.
Unser Tuning Tipp: RPM Teile sind aus nahezu unzerbrechlichem Nylon Kunstsoff für ungetrübten Fahrspass und ersetzen 1:1 das Originalteil
passt für: Slash 2WD, Slash 4x4, ECX Torment 4x4, Losi SCTE
nur für Fahrzeuge mit dem RPM Bumper Hinten
A serious issue with most currently available wheelie bars is the inability to use the truck as an off-road vehicle because most wheelie bars tend to stick out too far behind the truck. The RPM Low Visibility Wheelie Bar solves that problem! Since our wheelie bar and included wheels sits inside the protection of the rear bumper, they don’t stick out allowing the truck to function normally when rippin’ up the local track, yet still do their job when the occasional heavy finger pull yanks the front wheels off of the ground!
The RPM Low Visibility Wheelie Bar design bolts directly to all RPM Slash bumpers (both 2wd and 4×4), Losi SCTE & ECX Torment 4×4 at the mud flap mounts, while still allowing the use of RPM Mud Flaps (RPM #81012) as well as our Losi SCTE Bumper Mounts (RPM #73312! The RPM Wheelie Bar stays tucked up behind the rear bumper, yet sitting low enough to allow the wheels to touch down once the front end starts catching some serious air! Now any Slash, SCTE or Torment 4×4 owner can pull some sick wheel stands without the fear of grinding crucial rear bumper support components into dust!
RPM Low Visibility Wheelie Bars are sold ready to install on an RPM Rear bumper (sold separately) with all necessary mounting hardware and complete instructions for assembly. RPM Low Visibility Wheelie Bars are manufactured from our trademark blend of incredibly strong nylons and backed by our limited lifetime warranty again breakage.
Tech Notes: RPM Low Visibility Wheelie Bars are designed for use with RPM Slash 2wd and Slash 4×4 rear bumpers, ECX Torment 4×4 rear bumpers as well as our Losi SCTE Rear Bumper Mounts exclusively and will not work with stock Traxxas Slash rear bumpers, ECX Torment 4×4 rear bumpers or Losi SCTE rear bumper mounts.
Kundenbewertungen für "81312 RPM Low Visibiltiy Wheelie Bars Slash 4x4 Schwarz"
Bewertung schreiben
Weiterführende Links zu "81312 RPM Low Visibiltiy Wheelie Bars Slash 4x4 Schwarz"